If you’re looking to install flashing on an existing roof there are some factors you’ll have to take into consideration. First, you’ll want to make sure your roof’s in great shape and there aren’t any leaks. After you’ve verified that the roof is in good shape, you’ll need to measure the area where you’ll be installing the flashing. After you’ve measured your area, you’ll need to cut the flashing to size and then install it using nails or screws.
A new Roof Installation in Westminster can be difficult and demanding. It is essential to hire a professional in order to have a flawless new Roof Installation in Westminster! SoCal Green will provide you with your Roof Installation in Westminsters and maintenance needs.
Take a look at the area to be illuminated
The measurement of the area to be flashed is an important first step to install flashing onto an old roof. It is important to know the dimensions of the area that will be flashed, so that you are able to purchase the right quantity of flashing material. In addition taking measurements of the size of the area will provide you with a better comprehension of the structure of the roof and the way in which the flashing will need to be installed.
Cut flashing to size
Start with cutting your flashing down to size. When you’re working with a pan that’s already formed then you’ll need to cut it to extend 6 inches beyond the roof’s edge. In the case of roll roofing, cut the flashing twice the length of the length of the roof. Then cut the flashing in two vertically so that you’ll have two pieces which are the same size as the length of the roof.
Get rid of any old shingles or nails
In order to install flashing on a roof that’s already in place, first, you’ll have to remove any old shingles and nails. Once you’ve done that, you can install the new flashing. Make sure to overlap the flashing with at least 2 inches, and use corrosion-resistant nails and screws to secure it in the right place.
Secure flashing onto the roof
If your home has an roofing system that is in place, you’ll need be extra careful in putting up flashing. It’s the first thing to do is remove any shingles or other materials which might be blocking your path. After the roof is cleared then you’ll have be able to cut and measure the flashing to fit. Be sure to leave enough for an overlap so that the flashing is securely fixed to the roof. Once the flashing has been put installed, you are able to apply the new shingles or other roofing materials.
Nail flashing held in the right place
1. Make sure that the surface is free of dirt.
2. Find the area that needs to be covered, then cut the flashing according to the area.
3. Apply a generous amount of adhesive on the back of the flashing.
4. Press the flashing into place and then hold it for a few minutes to let the adhesive be set.
5. Nail the flashing in place using roofing nails.
6. Apply a bead of sealant around the outside of the flashing, ensuring that it is sealed it in place.
Seal the seams with roofing cement
After you have cut the strips of flashing to length, spread them out on the roof, so they cover the roof’s joints material by minimum 2 inches. Once the flashing is positioned, apply a continuous bead of roofing cement to the surface of the overlap. Use a putty knife to smooth out the cement and then remove any excess.
Apply caulk all over the flashing
In order to install roofing flashing it is necessary to apply caulk around the flashing. Begin by removing any previous caulk and other debris from the area. Then, apply a large amount of caulk to the side of the flashing that is below it. Make sure to smooth it out until it’s even and level. After that, press the flashing into position and seal it with more caulk.
Install additional shingles if needed
If you’re installing flashing on your old roof structure, it may require additional shingles to create an adequate surface for flashing to stick to. Begin by removing any damaged or missing shingles. Then, put the new shingles in place. Make sure you overlap the shingles to ensure that the flashing is completely covered.
If you’re thinking about installing flashing on your current roof There are a few things to be aware of. First, ensure that you’ve got the proper tools and materials. Then, take your time and ensure that you don’t damage your roof. If you’re not certain about what you’re doing it’s best to engage a professional. With a bit of planning and attention you can put flashing on your roof to keep your home in great condition for many years to be.
