SoCal Green Roofing Of Los Angeles
License# 1057764
Serving in Los Angeles & Surrounding Areas
License# 1057764

How To Install Flashing On An An Existing Roof In Monrovia?

If you’re considering installing flashing on an existing roof, there are a few aspects you’ll need to consider. First, you’ll need to make sure that the roof is in good shape and there aren’t leaks. Once you’ve established that the roofing is in excellent repair, you’ll need to measure the area where you’ll be installing the flashing. Once you’ve measured the area, you’ll have to cut the flashing to size and then put it in place using nails or screws.

A new Roof Installation in Monrovia can be hectic and critical. It is essential to hire a professional in order to get a perfect new Roof Installation in Monrovia! SoCal Green is here to provide you with your roof maintenance and installations.

Measure the area to be flashed

Measurement of the area that will be flashed is a crucial first step to install flashing onto an old roof. You will need to know the size of the area that will be flashed in order that you can purchase the right amount of flashing materials. In addition taking measurements of the size of the area will provide you with more understanding of the roof structure and how the flashing be placed.

Cut flashing to size

Begin in cutting off the flashing to size. In the case of a pan that’s already formed then you’ll need to cut it to extend 6 inches over the roof’s edge. For roll roofs, you’ll need to cut it twice the length of the width of the roof. Then, cut the flashing in two vertically so that you’ll have two pieces which are the same size as the length of the roof.

Get rid of any old shingles or nails

In order to install flashing on an existing roof, first, you’ll have to remove the old shingles and nails. Once you’ve done that then you can put in the new flashing. Make sure to overlap the new flashing by at least 2 inches and use corrosion-resistant nails or screws to hold it in position.

Install flashing securely onto the roof

If your home has an existing roof, you’ll need to take special care in putting up flashing. First, remove any shingles or other materials which might be blocking your path. After the roof is cleared, you’ll need be able to cut and measure the flashing to suit. Be sure to leave enough of an overlap so that the flashing is secure attached on the roof. Once the flashing is set, you can install the new shingles or other roofing materials.

Nail flashing held in place

1. Check that the surface is free of any debris.

2. Find the area that needs to be covered, then cut the flashing to size.

3. Apply a good amount of adhesive on the side of the flashing.

4. Apply the flashing and hold it there for a couple of minutes to allow the adhesive to set.

5. Attach the flashing using roofing nails.

6. Apply a bead of sealant along the edges of the flashing, ensuring that it is sealed it in the right place.

Seal the seams with roofing cement

Once you’ve cut the strips of flashing to the desired length, lay them out on the roof, so that they overlap the joint in the roofing material by minimum 2 inches. Once you have the flashing positioned, apply a continuous bead of roofing cement on the surface of the overlap. Utilize a putty blade to smooth out the cement and then remove any excess.

Apply caulk around the flashing

In order to install flashing on an existing roof, you’ll need to apply caulk to the flashing. Start by cleaning any old caulk and other debris off the surface. After that, apply a substantial amount of caulk on the underside of the flashing. Be sure to smooth it out until it’s level and even. After that press the flashing into the desired position, and seal it using more caulk.

Install additional shingles if necessary.

If you are installing flashing on your old roof structure, it might require the installation of additional shingles in order to create an adequate surface for flashing to adhere to. Start by removing any damaged or missing shingles. Then, put the new shingles in their place. Be sure to overlap the shingles so that the flashing will be completely fully covered.

If you’re considering installing flashing on your current roof there are some things you need to consider. First, make sure you’re using the correct tools and materials. Second, take your time and ensure that you don’t cause damage to your roof. Thirdly, if you’re unsure of what you’re doing it’s best to engage an expert. With a bit of planning and care it is possible to install flashing on your roof to keep your home in great shape for years to come.

How To Install synthetic Roof Underlayment in Monrovia?
What is the correct way to Install Metal Roofing in Monrovia?

Recent Posts

Recent Posts

Request a
Free Quote

Our mission at SoCal Green Roofing & Builders is to be your go-to roofing contractor in the Los Angeles area. We provide services throughout the greater Los Angeles area, Orange, San Bernardino, and Ventura Counties.

CALL US NOW

Schedule Your Appointment

"*" indicates required fields

MM slash DD slash YYYY
This field is for validation purposes and should be left unchanged.