If you’re considering installing flashing on an existing roof there are some factors you’ll have to take into consideration. First, you’ll need to make sure your roof’s in great shape and there aren’t leaks. Once you’ve confirmed that your roof’s in great repair, you’ll need to measure the area where you’ll be installing the flashing. After you’ve measured your space, you’ll need cut the flashing to size and then install it using screws or nails.
The process of a new Roof Installation in Stanton can be difficult and demanding. It is essential to hire a professional in order to get the perfect new Roof Installation in Stanton! SoCal Green will provide you with your roof maintenance and installations.
Take a look at the area to be flashed
The measurement of the area to be flashed is an important first step in the process installation of flashing to an already existing roofing. It is essential to determine the dimensions of the area to be flashed, so that you are able to purchase the correct amount of flashing materials. Also taking measurements of the space will provide a better comprehension of the structure of the roof and how the flashing need to be installed.
Cut flashings to the size you need
Start in cutting off the flashing into size. When you’re working with a pan that’s already formed it’s just necessary to cut it to extend 6 inches over the roof’s edge. For roll roofs, make the flashing cut twice as long as the width that the roofing. Then, cut the flashing horizontally in half to create two pieces which are the same size as the length of the roof.
Get rid of any old shingles or nails
In order to install flashing on an existing roof you’ll first need to remove any old shingles and nails. Once that’s done, you can install the flashing. Be sure to cover the flashing with minimum 2 inches and use corrosion-resistant nails and screws to hold it in the right place.
Install flashing securely onto the roof
If your home has an roofing system that is in place, you’ll need to take special care in putting up flashing. It’s the first thing to do is remove any shingles or other material that might be blocking the path. When the roof is clean, you’ll need take measurements and then cut your flashing to suit. Make sure that you leave enough of an overlap to ensure that the flashing is secure fixed onto the roofing. Once the flashing is set, you can put up the new shingles or other materials.
Nail flashing held in place
1. Make sure that the surface is free of dirt.
2. Take a measurement of the area to be covered, then cut the flashing according to the area.
3. Apply a good amount of adhesive on the side of the flashing.
4. Apply the flashing and then hold it for a couple of minutes to allow the adhesive to be set.
5. Nail the flashing in place with roofing nails.
6. Apply a small amount of sealant around the outside of the flashing to secure it in the right place.
Cover the seams using roofing cement
After cutting the flashing strips to the desired length, lay them out on the roof, so that they overlap the roof’s joints material by at least 2 inches. Once the flashing is set, apply a continuous bead of roofing cement to the surface of the overlap. Utilize a putty blade to smooth out the cement and then remove any excess.
Apply caulk all over the flashing
To install flashing on an existing roof you’ll need to apply caulk to the flashing. Start by cleaning any old caulk and debris from the area. After that, apply a substantial amount of caulk to underneath of the flashing. Make sure to smooth it so that it’s level and even. Then, press the flashing into place and seal it with more caulk.
Install additional shingles as needed.
If you’re installing flashing on your existing roof, you might require additional shingles to provide a solid surface for the flashing to stick to. Start by removing any loose or damaged shingles. Then, apply the new shingles into place. Be sure to cover the shingles in order that the flashing will be completely fully covered.
If you’re thinking about installing flashing on your existing roof there are some things you need to be aware of. First, make sure you have the right tools and materials. Also, be patient and ensure that you don’t harm your roof. If you’re not certain about the right thing to do you should employ a professional. With a little bit of planning and attention it is possible to install flashing on your roof to ensure that your home is in good condition for the years to be.
Is it faster to install Metal Roof Over Shingles in Stanton?
Should I Get A New Roof Before Installing Solar Panels in Stanton?
