Serving Residents in Los Angeles & Surrounding Areas
License# 1057764
Serving in Los Angeles & Surrounding Areas
License# 1057764
Blog

How Do I Install Flashing On Existing Roof In Santa Ana?

If you’re considering installing flashing on an existing roof there are some things you’ll need to consider. First, you’ll want to make sure that your roofing is in excellent shape and that there are no leaks. Once you’ve established that the roof is in good shape it’s time to measure the area where you’ll install the flashing. Once you’ve measured the area, you’ll have to cut the flashing to size and then put it in place using nails or screws.

A new Roof Installation in Santa Ana can be stressful and challenging. It is essential to hire a professional in order to get the perfect new Roof Installation in Santa Ana! SoCal Green will assist you with your roofing maintenance and installation needs.

Take a look at the area to be illuminated

The measurement of the area to be flashed is the first step installation of flashing to an already existing roofing. It is important to know the measurements of the area to be flashed in order that you are able to purchase the right quantity of flashing material. Also taking measurements of the size of the area will provide you with a better understanding of the structure of your roof and how the flashing need to be installed.

Cut flashings to the size you need

Begin by cutting the flashing into size. In the case of a pre-formed pan, you’ll just need to cut it to extend 6 inches past the edge of the roof. If you’re using roll roofing, cut the flashing twice the length of the width of the roof. Then, cut the flashing in half vertically so that you’ll have two pieces with the same length as the width of the roof.

Take off any old shingles and nails

In order to install flashing on an existing roof, first, you’ll have to remove the old shingles and nails. Once you’ve done that then you can put in the flashing. Be sure to cover the flashing with minimum 2 inches and use corrosion-resistant nails and screws to secure it into the right place.

Make sure that flashing is secured to the roof

If your home has an already-existing roof, you’ll have to be careful for installing the flashing. First, take off any shingles or other materials which might be blocking the path. Once the area is clear it’s time to measure and cut the flashing to fit. Be sure to leave enough of an overlap to ensure that the flashing is secure fixed onto the roofing. Once the flashing is in place, you can put up the new shingles or other roofing materials.

Nail flashing held in the right place

1. Make sure that the surface is clean and free of debris.

2. Take a measurement of the area to be covered and cut the flashing according to the area.

3. Apply a good amount of adhesive to the side of the flashing.

4. Place the flashing in place and then hold it for a couple of minutes to allow the adhesive to set.

5. Fix the flashing with roofing nails.

6. Apply a bead of sealant along the edges of the flashing to secure it in place.

Seal the seams with roofing cement

After cutting the strips of flashing to size, lay them out on the roof in a way they cover the roof’s joints material by at least 2 inches. Once you have the flashing positioned on the roof, apply a continuous layer of roofing cement to the underside of the overlap. Utilize a putty blade for smoothing the cement and remove any excess.

Apply caulk around the flashing

To install the flashing onto an already-existing roof it is necessary to apply caulk to the flashing. Begin by removing any previous caulk and other debris from the area. After that, apply a substantial amount of caulk to the side of the flashing that is below it. Be sure to smooth it out so that it’s level and even. Then apply the flashing in position and seal it with more caulk.

Install additional shingles if necessary.

If you’re installing flashing on your old roof structure, it may require additional shingles to create an even surface for the flashing to adhere to. Begin by removing any damaged or missing shingles. Next, you need to nail the new shingles in their place. Make sure you overlap the shingles so that the flashing is completely fully covered.

If you’re thinking about adding flashing to your existing roof, there are a few points to keep in mind. First, be sure that you have the right tools and materials. Also, be patient and ensure that you don’t cause damage to your roof. And third, if you’re unsure of what you’re doing, it’s always best to engage a professional. With just a little planning and care it is possible to install flashing on your roof to ensure that your home is in good shape for long time to be.

Do homeowners insurance policies cover incorrectly installed roofing in Santa Ana?
What is the best way To Install Metal Roofing in Santa Ana?

Request a
Free Quote

Our mission at SoCal Green Roofing & Builders is to be your go-to roofing contractor in the Los Angeles area. We provide services throughout the greater Los Angeles area, Orange, San Bernardino, and Ventura Counties.

CALL US NOW

Schedule Your Appointment

"*" indicates required fields

MM slash DD slash YYYY
This field is for validation purposes and should be left unchanged.