If you’re looking to install flashing on your roof there are some factors you’ll have to consider. First, you’ll need to ensure that your roofing is in excellent shape and there aren’t leaks. Once you’ve established that your roof’s in great shape then you’ll have to determine the area in which you’ll be installing the flashing. After you’ve measured the area, you’ll need to cut the flashing to fit and then put it in place using screws or nails.
An new Roof Installation in Santa Fe Springs can be difficult and demanding. You’ll need a professional order to get a perfect new Roof Installation in Santa Fe Springs! SoCal Green can assist you with your roof maintenance and installations.
Determine the area that will be flashed
The measurement of the area to be flashed is the initial step to install flashing onto an old roof. It is essential to determine the dimensions of the area that will be flashed in order that you can buy the correct amount of flashing material. Additionally taking measurements of the area will give you a better understanding of the structure of your roof and the way in which the flashing will be placed.
Cut flashing to size
Start in cutting off the flashing into size. When you’re working with a pan that’s already formed then you’ll need to cut it long enough to extend 6 inches past the edge of the roof. In the case of roll roofing you’ll need to cut it twice as long as the length that the roofing. Then cut the flashing horizontally in half so that you have two pieces that are the same length as the length of the roof.
Take off any old shingles and nails
To install flashing on an existing roof, first you’ll need to take off any old nails and shingles. Once that’s done, you can install your new flashing. Make sure that you overlap the new flashing by at least 2 inches, and then use corrosion-resistant nails or screws to secure it into the right place.
Secure flashing onto the roof
If your home has an already-existing roof, you’ll have to take special care when installing flashing. First, eliminate any shingles or other material that might be blocking the path. After the roof is cleared it’s time to measure and cut the flashing to fit. Make sure you leave plenty for an overlap so that the flashing is securely attached on the roof. Once the flashing has been put set, you can apply the new roof shingles or other materials.
Nail flashing that is in the right place
1. Make sure the surface is clean and free of debris.
2. Find the area that needs to be covered and cut the flashing according to the area.
3. Apply a large amount of adhesive to the reverse of the flashing.
4. Place the flashing in place and then hold it for a few minutes in order to let the adhesive set.
5. Nail the flashing in place using roofing nails.
6. Apply a bead of sealant around the perimeter of the flashing to secure it in position.
Cover the seams using roofing cement
After you have cut the strips of flashing to length, spread them out on the roof, so that they overlap the joints in the roofing material by minimum 2 inches. Once the flashing is placed on the roof, apply a continuous layer of roofing cement on the bottom of the overlap. Utilize a putty blade to smooth out the cement, and then take off any excess.
Apply caulk to the flashing area.
In order to install flashing on an existing roof, it is necessary to apply caulk to the flashing. Begin by removing any previous caulk or debris off the surface. Next, apply a generous amount of caulk to side of the flashing that is below it. Be sure to smooth it out so that it’s level and even. Finally press the flashing into place and seal it with more caulk.
Install additional shingles if needed
If you are installing flashing on an existing roof, you might require additional shingles in order to create a solid surface for the flashing to stick to. Start by removing any damaged or loose shingles, then put the new shingles in place. Make sure you overlap the shingles to ensure that the flashing is completely protected.
If you’re thinking of installing flashing on your existing roof, there are a few things to keep in mind. First, ensure that you’re using the correct equipment and materials. Second, take your time and make sure you don’t harm your roof. And third, if you’re not certain about the right thing to do you should employ a professional. With just a little planning and care, you can install flashing on your roof and ensure that your home is in good condition for many years to be.